ANSERGLOB facade paint ECO+

Advantages

Ecologically friendly
Resistant to weather
For interior and exterior use
High covering capacity
Resistant to abrasion and washing

Technical data

Gloss	Matte
Density	1,55 g/cm³
Resistance to wet abrasion	1 class (DSTU EN 13300)
VOC Content	< 40 g/l
Spreading rate	Approx. 150 g/cm²
Time before overcoating	1-2 hours
Resistance to the diffusion of water vapors, Sd	No more than 0,15 m
Coefficient of water absorption	No more 0,1 kg/г/m² h ^0,5
Resistant to atmospheric precipitation	24 hours
Surface temperature	from +5°С to +30°С
Exploitation temperature	from -30°С to +80°

Make tint

Download
instruction

Consumption
calculator

Colors
catalogue

Product certificates

Facade acrylic paint ANSERGLOB ECO+ is used for high quality coating interior and exterior walls and ceilings and also as the finishing decorative coating in the exterior insulation finishing system ANSERGLOB. It is applied on any mineral substrates as concrete, brickwork, cement and cement-lime mortars (humidity less than 4%) gypsum mortars and drywall (humidity less than 1 %) etc, and on the organic substrates (plywood, fiberboard, particleboard, OSB, wallpapers). It is used for renewal of painted coating on decorative plasters. Facade acrylic paint ANSERGLOB ECO+ (white base) is tinted by the COLOR SYSTEM or used in basic white color.

Composition
Facade acrylic paint ANSERGLOB ECO+ is produced on the base of acrylic dispersion with mineral fillers and functional additives.

Storage
Keep it dry indoors in original package. Guaranteed term of storage is 24 month from production date at temperature above +5°С and below +30°С

Safety
Eye contact: wash eyes with clear water for several minutes and obtain medical attention if necessary. Use latex gloves to protect hands. Compliant to technical conditions TU В. 2.7-20.324962264-005:2012

The surface preparation is realized according to State Standard of Ukraine (DSTU N B A.3.1-23:2013) and State Building Codes of Ukraine (DBN В.2.6-22-2001). Surface must be structurally sound, clean, dry and free from dust, lime, grease, dirt, oil or emulsion paints. While repair works and before applying the paint fragile areas of the substrate should be thoroughly removed. The cracks into the substrate must be filled up with the one of the ANSERGLOB products (for an example, small cracks is filled up by the ANSERGLOB BCT 25 or BCT 27). Before applied the paint solid and dense mineral substrates as brickwork, concrete beds, cement-sand and cement-lime mortars, gypsum mortars and wooden surfaces should be previously treated by the one of deep penetrating primers ANSERGLOB. Weak mineral substrates should be cleaned till solid layer. The coatings based on synthetic paints must be removed and treated by the one of deep penetrating primers ANSERGLOB. Facade acrylic paint ANSERGLOB ECO+ is applied after 4 hours after grouting by primer.

Before applied facade acrylic paint ANSERGLOB ECO+ must be well mixed by the drill on low revs. The paint is applied on the surface in one or two layers by the brush, block brush, roller (felt, foam rubber) or sprayer. Application on the same surface must be provided continuously according to the rule "wet on wet". Paint can be diluted by water (but no more then 5 % from paint weight) for the first layer of coating. It is not recommended to dilute paint by water for the second layer of coating and the next ones. Depending on the temperature and humidity conditions second layer of coating is applied after 1-2 hours after the first one. The surface applied with acrylic facade paint Anserglob ECO+ is resistant to the mechanical treatment. When applied avoid the drying of the paint and wash the hands and tools by water.

Note:Application should be complied at temperature above +5 °С and below +30 °С. All the mentioned recommendations are effective at temperature of +20 °С and air humidity of 60 %. Under the other conditions drying time may be changed. Do not use for substrates constantly exposed to stress (floors). For identity of the substrate color it is recommended to use one batch production.
While applying the paint the surface must be protected from the direct sun rays and excess wetting (rain, fog).

Consumption of facade acrylic paint is 0,15-0,35 kg per m² in average.