facebook

ANSERGLOB «Acryl»

Advantages

  • Ecologically friendly
  • Resistant to weather
  • For interior and exterior use
  • High covering capacity
  • Resistant to abrasion and washing

Technical data

Gloss Matte
Density 1,55 g/cm3
Spreading rate Approx. 150 g/cm2
Time before overcoating 1-2 hours
Resistance to the diffusion
of water vapors, Sd
No more than 0,15 m
Resistant to
atmospheric precipitation
After 12 hours
Surface temperature from +5°С to +30°С
Exploitation temperature from -30°С to +80°
Facade acrylic paint ANSERGLOB is used for coating interior and exterior walls of the buildings also as the finishing decorative coating in the exterior insulation finishing system ANSERGLOB. It is applied on any mineral substrates as concrete, brickwork, cement and cement-lime mortars (humidity less than 4%) gypsum mortars and drywall (humidity less than 1 %) etc, and on the organic substrates (plywood, fiberboard, particleboard, OSB, wallpapers). Facade acrylic paint ANSERGLOB is used for renewing of the painting coating of the decorative plasters. Facade acrylic paint ANSERGLOB (white base) is tinted by the COLOR SYSTEM or used in basic white color.

Note: facade acrylic paint ANSERGLOB (T base) is used only after tinting by the COLOR SYSTEM.

The surface preparation is realized according to State Standard of Ukraine (DSTU N B A.3.1-23:2013) and State Building Codes of Ukraine (DBN В.2.6-22-2001). Surface must be structurally sound, clean, dry and free from dust, lime, grease, dirt, oil or emulsion paints. While repair works and before applying the paint fragile areas of the substrate should be thoroughly removed. The cracks into the substrate must be filled up with the one of the ANSERGLOB products (for an example, small cracks is filled up by the ANSERGLOB BCT 25 or BCT 27). Before applied the paint solid and dense mineral substrates as brick-work, concrete beds, cement-sand and cement-lime mortars, gypsum mortars and wooden surfaces should be previously treated by the one of deep penetrating primers ANSERGLOB. Weak mineral substrates should be cleaned till solid layer. The coatings based on synthetic paints must be removed and treated by the one of deep penetrating primers ANSERGLOB. Facade acrylic paint ANSERGLOB is applied after 4 hours after grouting by primer.
Before applied facade acrylic paint ANSERGLOB must be well mixed by the drill on low revs. The paint is applied on the surface in one or two layers by the brush, block brush, roller (felt, foam rubber) or sprayer. Application on the same surface must be provided continuously according to the rule "wet on wet". Paint can be diluted by water (but no more then 5 % from paint weight) for the first layer of coating. It is not recom-mended to dilute paint by water for the second layer of coating and the next ones. Depending on the weather conditions second layer of coating is applied after 1-2 hours after the first one. Painted surface is resistant to mechanical treatment. When applied avoid the drying of the paint and wash the hands and tools by water.

Note: Application should be complied at temperature above +5 °С and below +30 °С. All the mentioned recom-mendations are effective at temperature of +20 °С and air humidity of 60 %. Under the other conditions dry-ing time may be changed. For identity of the facade color it is recommended to use one batch production. While applying the acrylic paint the surface must be protected from the direct sun rays and excess wetting (rain, fog).

Consumption of facade acrylic paint is 0,15-0,35 kg per m2 in average.

Can be used with other our products

Related products

X

Become a reseller

Leave your contact information, we will contact you shortly to discuss cooperation

X

FORM FOAM

X

Thank you, the application has been successfully sent!
Our manager will contact you as soon as possible

X

Thanks, your order has been successfully sent!
Our manager will contact you shortly

X

I want to work in anserglob






(doc, docx, pdf)

Attach resume