Silicone facade paint Anserglob Gazobeton is used to create the decorative thinlayer coating as interior as exterior surfaces and also as the finishing decorative coating in the exterior insulation finishing system ANSERGLOB. It is applied on mineral substrates as cement-sand, cement-lime mortars (after 28 days, humidity less than 4%) gypsum mortars (humidity less than 1 %), concrete beds (after 3 months, humidity less then 4 %); brickwork (after 28 days) and on organic surfaces (polystyrene slabs, plywood, fiberboard, particleboard, OSB). Silicone facade paint Anserglob Gazobeton is tinted by the COLOR SYSTEM or used in basic white color. It is recommended to surfaces for high permeability and waterproof properties.
Silicone facade paint Anserglob Gazobeton is produced on the base of silicone and acrylic dispersion with mineral fillers and functional additives.
Keep it dry indoors in original package. Guaranteed term of storage is 18 month from production date at humidity not more than 70%. Do not freeze.
Eye contact: wash eyes with clear water for several minutes and obtain medical attention if necessary. Use latex gloves to protect hands.
Compliant to technical conditions TU В. 2.7-20.324962264-005:2012
The surface preparation is realized according to State Standard of Ukraine (DSTU N B A.3.1-23:2013) and State Building Codes of Ukraine (DBN В.2.6-22-2001). Surface must be structurally sound, clean, dry and free from dust, lime, grease, dirt, oil or emulsion paints. While repair works and before applying the paint fragile areas of the substrate should be thoroughly removed. The surface irregularity till 3 mm must be leveled by the finishing putty ANSERGLOB ВСТ 25, big irregularities – by the plastering mortar ANSERGLOB ВСТ 20.
Before applied the paint solid and dense cement-sand and cement-lime mortars, concrete beds and also brickwork must be previously treated by silicone adhesion primer ANSERGLOB EG 62. The gypsum and surfaces with strong water sorption must be previously treated by the one of deep penetrating primers ANSERGLOB, exposed till full drying and after that should be treated by silicone adhesion primer ANSERGLOB EG 62. The coatings based on oil or synthetic paints must be removed in the mechanical way or by the solvent treatment then all the surface must be treated by silicone adhesion primer ANSERGLOB EG 62. Silicone facade paint Anserglob Gazobeton is applied after 4 hours after applying of primer. Previously silicone adhesion emulsion ANSERGLOB EG 62 must be tinted in similar color of applying paint.
Before applied acrylic facade paint Anserglob Gazobeton must be well mixed by the drill on low revs. The paint is applied on the surface in one or two layers by the spatula and then with different tools (brush, structural roller, and spatula) and desired structure given. While adding water (no more than 1%) to facade paint composition it could be applied with roller. Application on the same surface must be provided continuously according to the rule "wet on wet". In the case of application break masking tape along the line where you plan to stop working should be sticked, apply the paint with the offset on the masking tape then remove the masking tape with the remnants of paint. The surface applied with acrylic facade paint Anserglob Gazobeton is resistant to the mechanical treatment. When applied avoid the drying of the paint and wash the hands and tools by water.
Note:Application should be complied at temperature above +5 °С and below +30 °С. All the mentioned recommendations are effective at temperature of +20 °С and air humidity of 60 %. Under the other conditions drying time may be changed. For identity of the facade color it is recommended to use one batch production.
While applying the acrylic paint the surface must be protected from the direct sun rays and excess wetting (rain, fog).
Consumption of silicone facade paint Anserglob Gazobeton is 0,7 kg/m2 average.