facebook

ANSERGLOB «Structural»

Advantages

  • Ecologically friendly
  • Hydrophobic
  • Resistant to damage
  • For interior and exterior use
  • Resistance to pollution
  • Elastic

Technical data

Density 1,6 g/cm33
Forming time of
the surface film
15 minutes
Adhesion to the substrate Not less than 0,5 MPa
Resistant to
atmospheric precipitation
After 24 hours
Water-vapor permeability Not less than 0,03 mg/m∙g∙Pa
Surface temperature from +5°С to +30°С
Exploitation temperature from -30°С to +80°
Structural acrylic paint ANSERGLOB is used to create the decorative thinlayer coating as interior as exterior surfaces also as the finishing decorative coating in the exterior insulation finishing system ANSERGLOB. It is applied on any substrates as cement-sand, cement-lime mortars (after 28 days, humidity less than 4%) gypsum mortars (humidity less than 1 %), concrete beds (after 3 months, humidity less then 4 %); brickwork (after 28 days) and on organic surfaces (polystyrene slabs, plywood, fiberboard, particleboard, OSB). Struc-tural acrylic paint ANSERGLOB is tinted by the COLOR SYSTEM or used in basic white color.
The surface preparation is realized according to State Standard of Ukraine (DSTU N B A.3.1-23:2013) and State Building Codes of Ukraine (DBN В.2.6-22-2001). Surface must be structurally sound, clean, dry and free from dust, lime, grease, dirt, oil or emulsion paints. While repair works and before applying the paint fragile areas of the substrate should be thoroughly removed. The surface irregularity till 3 mm must be le-veled by the finishing putty ANSERGLOB ВСТ 25, big irregularities – by the plastering mortar ANSERGLOB ВСТ 20. The cracks till 0,15 mm should be filled by structural acrylic paint ANSERGLOB. Before applied the paint solid and dense cement-sand and cement-lime mortars, concrete beds must be pre-viously treated by the emulsion ANSERGLOB EG 62. The gypsum and surfaces with strong water sorption must be previously treated by the one of deep penetrating primers ANSERGLOB, and then should be treated by the emulsion ANSERGLOB EG 62 and exposed till full drying. The coatings based on oil or synthetic paints must be removed in the mechanical way or by the solvent treatment then all the surface must be treated by one of the deep penetrating primers ANSERGLOB. Structural acrylic paint ANSERGLOB is applied after 4 hours after grouting by primer.
Before applied structural acrylic paint ANSERGLOB must be well mixed by the drill on low revs. The paint is applied on the surface in one or two layers by the spatula or structural roller. Application on the same sur-face must be provided continuously according to the rule "wet on wet". In the case of application break should be sticked masking tape along the line where you plan to stop working, apply the paint with the offset on the masking tape and give it the desired texture. Then immediately remove the masking tape with the remnants of fresh plaster. The surface with applied on it structural acrylic paint ANSERGLOB is resistant to the mechanical treatment. When applied avoid the drying of the paint and wash the hands and tools by water.

Note:Application should be complied at temperature above +5 °С and below +30 °С. All the mentioned recom-mendations are effective at temperature of +20 °С and air humidity of 60 %. Under the other conditions dry-ing time may be changed. For identity of the facade color it is recommended to use one batch production. While applying the acrylic paint the surface must be protected from the direct sun rays and excess wetting (rain, fog).

ANSERGLOB «Structural»

Can be used with other our products

Related products

X

Become a reseller

Leave your contact information, we will contact you shortly to discuss cooperation

X

FORM FOAM

X

Thank you, the application has been successfully sent!
Our manager will contact you as soon as possible

X

Thanks, your order has been successfully sent!
Our manager will contact you shortly

X

I want to work in anserglob






(doc, docx, pdf)

Attach resume