ANSERGLOB WSR 56

Advantages

  • Permeable
  • Freezeproof
  • Ecologically friendly
  • Waterproof
  • High adhesion to the surface

Technical data

Thickness of layer 2-5 mm
Mixture ratio:
Plastic consistency 0,21 L per kg of mixture
Liquid consistency 0,24 L per kg of mixture
Adjustment time not less than 1 hours
Resistant to weather after 24 hours
Ready for primary stress 3 days
Overcoating 7 days
Compressive strength not less than 12 MPa
Adhesion to substrate not less than 1 MPa
Freeze-Thaw Stability not less than 50 cycles
Surface temperature from +5°С to +30°С
Exploitation temperature from -20°С to +60°С
Single-component waterproofing mortar ANSERGLOB WSR 56 is used for providing waterproofing works before plastering or cladding by ceramic tiles of building constructions: balconies, terraces, pools, foundations of hydraulic structures, reservoirs for storage of water, including drinking water, which does not operate under pressure at a depth till 5 m. Waterproofing is carried out on concrete beds (after not less than 3 months, the strength is not less than 15 MPa), on brickwork, laid of similar material with filled joints (after not less than 28 days) on a cement-sand screeds and plasters (after not less than 28 days). It is used from the side of moisture affection.
The surface preparation is realized according to State Standard of Ukraine (DSTU N B A.3.1-23:2013) and State Building Codes of Ukraine (DBN В.2.6-22-2001). Surface must be structurally sound, clean, dry and free from dust, grease, dirt, lime, wax, oil or emulsion paints and other substances that reduce adhesion. Surface irregularities must be smoothed; fragile areas of substrate must be removed. Depending on substrate origin, surface preparation is realized by sand blasting, or by water under pressure, or manually. The surface of the substrate must be level but coarse. Cracks in substrate must be expanded and treated by deep penetrating emulsions ANSERGLOB and filled by plastering mortar ANSERGLOB BCT 20 or ANSERGLOB ВСТ 27. The edges and corners should be rounded to a radius not less than 4 cm. Before applying ANSERGLOB WSR 56 substrate must be wetted, avoiding appearing of a continuous water film, surface must not be treated by any primers.
Prepared mortar is applied with a brush or spatula on damped but not wetted surface in same direction without cross movements, according to method "wet on wet". Overcoating layer is applied in a perpendicular direction to the previous one. Before the end of the work it is required to make sure that all the surface is equally covered by mortar. Applying waterproofing mortar, the minimal thickness of layer must be 2 mm. The maximal thickness of all layers of waterproofing mortar must not exceed 5 mm. While applying and just applied waterproofing layer must be protected from fast drying, draughts and direct sunrays.
Waterproofing layer based on mortar ANSERGLOB WSR 56 is not designed for heavy mechanical stress. After 3 days waterproofing layer is ready for primary stress. After 7 days it is required to cover surface by ceramic tiles, applying adhesive mortars ANSERGLOB or plastering mortars ANSERGLOB BCT 20 or ANSERGLOB BCT 22.

Note: Application should be complied at temperature above +5°С and below +30°С. All the mentioned recommendations are effective at temperature of +20°С and air humidity of 60%. Under the other conditions crusting, stiffening and curing time may be changed.

Wetting order Thickness of layer, mm Consumption, kg
Short-term stress (splashing water) 2,0-2,5 3,0- 3,8
Long-term stress (without water pressure) 2,5-3,5 3,8-5,3
Stressed by moisture external surfaces and building elements 3,5-5,0 5,3-7,5

Dry mixture must be poured into container with clear water with the room temperature when at the same time manually or mechanically mixed (by the drill on low revs) to obtain the kindred and elastic mass. Quantity of water depends on technology of application: applying by spatula (5,25-5,5 liters of water per 1 bag of 25 kg); applying by brush or block brush (5,5-6 liters of water per 1 bag of 25 kg). After exposing 5 min mortar must be mixed again and used during 2 hours.

Can be used with other our products

X

Become a reseller

Leave your contact information, we will contact you shortly to discuss cooperation

X

FORM FOAM

X

Thank you, the application has been successfully sent!
Our manager will contact you as soon as possible

X

Thanks, your order has been successfully sent!
Our manager will contact you shortly

X

I want to work in anserglob






(doc, docx, pdf)

Attach resume