• High adhesion
  • Freezeproof
  • Ecologically friendly
  • Resistant to weather
  • Highly plasticized

Technical data

Thickness of the layer 2-10 mm
Mixture ratio 0,20-0,22 L per kg of mixture
Adjustment time not less than 2 hours
Open time not less than 20 min
Time to correct not less than 10 min
Curing time 24 hours
Adhesion to substrate more than 1 MPa
Freeze-Thaw Stability not less than 50 cycles
Shear not more than 0,5 mm
Surface temperature from +5°С to +30°С
Exploitation temperature from -30°С to +80°С
Adhesive mortar ANSERGLOB BCX 33 is used for cladding on concrete, brickwork, cement-sand, cement-lime and also gypsum rigid surfaces, monolithic floors by ceramic, concrete tiles and artificial stone which have size not more than 400x400 mm and water sorption more than 1 %. Mortar can be used interior and exterior of industrial buildings and residential apartments, on terraces, balconies.
The surface preparation is realized according to State Standard of Ukraine (DSTU N B A.3.1-23:2013, DSTU N B A.2.6-212:2016) and State Building Codes of Ukraine (DBN В.2.6-162:2010). Surface must be structurally sound, clean, dry and free from dust, grease, dirt, lime, wax, oil or emulsion paints. Fragile areas of substrate must be removed. Surface irregularity till 10 mm must be leveled by mortar ANSERGLOB BCX 33, big irregularities of walls – by the plastering mortar ANSERGLOB ВСТ 20 and big irregularities of floors of by cement screed ANSERGLOB LFS 70. Before applying substrates with strong sorption must be treated by one of deeply penetrating emulsions ANSERGLOB and exposed for 4 hours. Before applying substrates with low sorption must be treated by ANSERGLOB EG 62 and exposed from 3 to 6 hours.
Prepared mortar should be spread by tile trowel, spatula or float on cladding surface. After applied mortar is combed by notch trowel or spatula with the U-shaped notches or square notches, which form equal combs of the same altitude on applied surface. Depending on thickness and dimensions of cladding tiles notch size of trowel is selected (for example, for tile size 20x20 cm trowels with the square notch size 6 mm and more are used). Tiles are installed in turn on the surface, covered by adhesive mortar, and pressed evenly. The tile can be moved during 10 min from the moment of installation if required. Thickness of adhesive layer between tile and substrate must be minimally 2 mm to show its full curing. Using handmade tile with unleveled back side and some cut ceramic and stone tile additional spreading of adhesive mortar by rectangular trowel on tile back side is required in order to achieve full contact between tile and substrate. Applying of adhesive mortar on back side of tile is additional measure and does not replace its spreading on the substrate. Joint width between tiles must be not less than 1,5 mm.
Tiles are prohibited to wet preliminary!


If the bag is marked WINTER, the mortar of adhesive and reinforcing ANSERGLOB BCX 40 is used at a temperature more then 0 °C. During the period of gaining strength of the mortar, it is allowed to reduce the ambient temperature to -5 ° C. The base for the mortar should not be frozen. All the above recommendations are effective at a relative humidity of 60%. In other conditions, the time of peeling, setting and curing may change. When performing works, the facade must be protected from high humidity (rain, fog, snow).

The work should be performed at a temperature of + 50C to + 300C. All the above recommendations are effective at a temperature of + 200C and a relative humidity of 60%. In other conditions, the time of peeling, setting and curing may change. When performing works, the facade should be protected from direct sunlight, as well as high humidity (rain, fog).

Average consumption of the mixture is 1,3 kg per m2 on 1 mm of layer.
Dry mixture must be poured into container with clear water according to ratio 0,20-0,22 liters of water per 1 kg of mixture (5,0-5,5 liters of water per 1 bag of 25 kg) when at the same time manually or mechanically mixed (by the drill on low revs) to obtain the kindred and elastic mass. After exposing 5 min mortar must be mixed again and used during 2 hours.

Can be used with other our products

Related products


Become a reseller

Leave your contact information, we will contact you shortly to discuss cooperation




Thank you, the application has been successfully sent!
Our manager will contact you as soon as possible


Thanks, your order has been successfully sent!
Our manager will contact you shortly


I want to work in anserglob

(doc, docx, pdf)

Attach resume