facebook

ANSERGLOB silicone «kamintseva»

Advantages

  • Permeable
  • Ecologically friendly
  • For interior and exterior use
  • Waterproof
  • Ready to use
  • Resistance to pollution

Technical data

Plastering layer thickness 1 mm; 1,5 mm; 2 mm
Density 1,6 g/cm3
Forming time of the surface film 15 minutes
Adhesion to the substrate Not less than 0,5 MPa
Resistant to
atmospheric precipitation
After 24 hours
Water-vapor permeability Not less than 0,05 mg/m∙g∙Pa
Surface temperature from +5°С to +30°С
Exploitation temperature from -30°С to +80°С
Decorative silicone plaster ANSERGLOB “Kamintseva” grain size 1 mm; 1,5 mm; 2 mm is used to create the decorative thinlayer plastering as interior as exterior surfaces also as the finishing decorative coating in the exterior insulation finishing system ANSERGLOB. It is applied on any substrates as cement-sand, ce-ment-lime mortars (after 28 days, humidity less than 4%) gypsum mortars (humidity less than 1 %), concrete beds (after 3 months, humidity less then 4 %), etc. It is recommended to use on the surface that needs good vapor permeability and waterproof properties.
The surface preparation is realized according to State Standard of Ukraine (DSTU N B A.3.1-23:2013) and State Building Codes of Ukraine (DBN В.2.6-22-2001). Surface must be structurally sound, clean, dry and free from dust, lime, grease, dirt, oil or emulsion paints. While repair works and before applying the plaster fragile areas of the substrate should be thoroughly removed. The surface irregularity till 3 mm must be le-veled by the finishing putty ANSERGLOB ВСТ 25, big irregularities – by the plastering mortar ANSERGLOB ВСТ 20.
Before applied the decorative plaster solid and dense cement-sand and cement-lime mortars, concrete beds must be previously treated by the emulsion ANSERGLOB EG 62. The gypsum and surfaces with strong water sorption must be previously treated by the one of deep penetrating primers ANSERGLOB, and then should be treated by the emulsion ANSERGLOB EG 62 and exposed till full dry-ing. The paint coatings and adhesive lime paints must be thoroughly removed and the surface must be treated by the emulsion ANSERGLOB EG 62. The coatings based on oil or synthetic paints must be re-moved in the mechanical way or by the solvent treatment then all the surface must be treated by the emulsion ANSERGLOB EG 62 and exposed not less then 3-6 hours.
It is recommended to use the emulsion adhesive ANSERGLOB EG 62 tinted in the similar color of the decorative plaster.
Before applied the bucket contents must be well mixed by the drill on low revs. Depending on the conditions of the applying the consistency of the mixture could be changed by adding the small quantity of clear water (no more tan 100 ml on 25 kg) and mixed again. The plaster is applied on the surface by stainless steel trowel which is held at an angle of 60 degrees to the surface. When the mortar stops sticking to the tool (2-5 minutes) the plaster is given the texture with a plastic float. While giving the texture the tool must be handed parallel to the surface. Depending on time, intensity and direction of moving of the plastic float could be achieved the horizontal, vertical, round or criss-crossed corrugated texture. Application on the same surface must be provided continuously according to the rule "wet on wet", avoiding drying of rubbed layers before applying the next ones. In the case of application break should be sticked masking tape along the line where you plan to stop working, apply the plaster with the offset on the masking tape and give it the desired tex-ture. Then immediately remove the masking tape with the remnants of fresh plaster.
Do not use corrosive containers and tools.

Note: The decorative plaster have been produced using of natural raw materials, because of it may contain dark crumbs or cracked crumbs. Too much action in giving the texture by the float may lead to the removal of pigment from the surface of the crumbs on the plaster tinted in the light colors. For identity of the facade color it is recommended to use one batch production. Applied plaster on the surface must be protected from atmospheric precipitation within 3 days. Application should be complied at temperature above +5 °С and below +30 °С. All the mentioned recommendations are effective at temperature of +20 °С and air humidity of 60 %. Under the other conditions drying time may be changed. While applying the facade must be pro-tected from the direct sun rays and also from the excess humidity (rain, fog).

Average consumption of the decorative plaster:
Grain size 1 mm – 1,6 kg/m22;
Grain size 1,5 mm – 2,5 kg/m2;
Grain size 2 mm – 3,0 kg/m22.

Can be used with other our products

Related products

X

Become a reseller

Leave your contact information, we will contact you shortly to discuss cooperation

X

FORM FOAM

X

Thank you, the application has been successfully sent!
Our manager will contact you as soon as possible

X

Thanks, your order has been successfully sent!
Our manager will contact you shortly

X

I want to work in anserglob






(doc, docx, pdf)

Attach resume